OpenAlex is a bibliographic catalogue of scientific papers, authors and institutions accessible in open access mode, named after the Library of Alexandria. It's citation coverage is excellent and I hope you will find utility in this listing of citing articles!
If you click the article title, you'll navigate to the article, as listed in CrossRef. If you click the Open Access links, you'll navigate to the "best Open Access location". Clicking the citation count will open this listing for that article. Lastly at the bottom of the page, you'll find basic pagination options.
Requested Article:
Enhanced mechanical properties of continuous carbon fiber reinforced polyether-ether-ketone composites via infrared preheating and high fiber volume fraction
Altuğ Uşun, Bahri Barış Vatandaş, Recep Gümrük
Additive manufacturing (2024) Vol. 89, pp. 104289-104289
Closed Access | Times Cited: 11
Altuğ Uşun, Bahri Barış Vatandaş, Recep Gümrük
Additive manufacturing (2024) Vol. 89, pp. 104289-104289
Closed Access | Times Cited: 11
Showing 11 citing articles:
Development of deformations in unidirectional carbon fiber – thermoplastic matrix composite materials under long‐term and cyclic loads
Andrey A. Stepashkin, Elena D. Makarova, Hussam Mohammad, et al.
Polymer Composites (2025)
Closed Access
Andrey A. Stepashkin, Elena D. Makarova, Hussam Mohammad, et al.
Polymer Composites (2025)
Closed Access
Crystallization behavior of thermoplastic resins near fibers and the influence of molding conditions during carbon fiber composite 3D printing
Yasuhiro Tasaka, Ryosuke Matsuzaki
Additive manufacturing (2025), pp. 104633-104633
Closed Access
Yasuhiro Tasaka, Ryosuke Matsuzaki
Additive manufacturing (2025), pp. 104633-104633
Closed Access
Toolpath generation for high density spatial fiber printing guided by principal stresses
Tianyu Zhang, Tao Liu, Neelotpal Dutta, et al.
Composites Part B Engineering (2025), pp. 112154-112154
Open Access
Tianyu Zhang, Tao Liu, Neelotpal Dutta, et al.
Composites Part B Engineering (2025), pp. 112154-112154
Open Access
Identifying thermal effects during 3D printing by comparing in-layer infrared pre- and postheating of carbon fiber reinforced polyamide 6
Ole S. Nesheim, Sindre Wold Eikevåg, Martin Steinert, et al.
Additive manufacturing (2025), pp. 104705-104705
Open Access
Ole S. Nesheim, Sindre Wold Eikevåg, Martin Steinert, et al.
Additive manufacturing (2025), pp. 104705-104705
Open Access
Optimization analysis of stiffness and natural frequency of unidirectional and randomly oriented short fiber-reinforced composite materials
Emmanuel Chukwueloka Onyibo, Aysegul Gazioglu, Mohammad Abulibdeh, et al.
Acta Mechanica (2025)
Open Access
Emmanuel Chukwueloka Onyibo, Aysegul Gazioglu, Mohammad Abulibdeh, et al.
Acta Mechanica (2025)
Open Access
Numerical and Experimental Investigation of Laser-Assisted Fused Filament Fabrication of Carbon Fibre Reinforced Polyether-Ether-Ketone Composites: Temperature Field Evolution and Crystallisation Behaviours
Wulin Qiu, Yingdan Zhu, Pengcheng Shi, et al.
(2025)
Closed Access
Wulin Qiu, Yingdan Zhu, Pengcheng Shi, et al.
(2025)
Closed Access
On the printability and inter-layer adhesion in 3D printing of continuous carbon fibre reinforced PEEK composite using tape and filament
Junaid Ahmad Qayyum, Aonan Li, Jiang Wu, et al.
Composites Part A Applied Science and Manufacturing (2024), pp. 108654-108654
Open Access | Times Cited: 2
Junaid Ahmad Qayyum, Aonan Li, Jiang Wu, et al.
Composites Part A Applied Science and Manufacturing (2024), pp. 108654-108654
Open Access | Times Cited: 2
Preparation of continuous carbon fiber reinforced PA6 prepreg filaments with high fiber volume fraction
Ming Zhang, Zhonggang Sun, Yingbing Liang, et al.
Additive Manufacturing Letters (2024), pp. 100245-100245
Open Access | Times Cited: 1
Ming Zhang, Zhonggang Sun, Yingbing Liang, et al.
Additive Manufacturing Letters (2024), pp. 100245-100245
Open Access | Times Cited: 1
Three-dimensional printing of high-performance continuous fiber-reinforced thermoplastic composites: causes and elimination of process-induced defects
Weijun Zhu, Long Fu, Xiaoyong Tian, et al.
Composites Part B Engineering (2024), pp. 112080-112080
Closed Access
Weijun Zhu, Long Fu, Xiaoyong Tian, et al.
Composites Part B Engineering (2024), pp. 112080-112080
Closed Access
Structural Integrity of Three Dimensional Printed Carbon Fiber Composites/Nanocomposites for Aeronautical Components—Current Scenarios and Opportunities
Ayesha Kausar
Advances in Materials Science (2024) Vol. 24, Iss. 4, pp. 67-96
Open Access
Ayesha Kausar
Advances in Materials Science (2024) Vol. 24, Iss. 4, pp. 67-96
Open Access
Infrared on-site heating for material extrusion additive manufacturing of carbon fiber filled polyphenylene sulfide and its nano-graphene-reinforced alternatives
Zhaogui Wang, Kexuan Zhou, Pengbo Xu
Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering (2024)
Closed Access
Zhaogui Wang, Kexuan Zhou, Pengbo Xu
Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering (2024)
Closed Access
