Open Access Helper

OpenAlex Citation Counts

OpenAlex Citations Logo

OpenAlex is a bibliographic catalogue of scientific papers, authors and institutions accessible in open access mode, named after the Library of Alexandria. It's citation coverage is excellent and I hope you will find utility in this listing of citing articles!

If you click the article title, you'll navigate to the article, as listed in CrossRef. If you click the Open Access links, you'll navigate to the "best Open Access location". Clicking the citation count will open this listing for that article. Lastly at the bottom of the page, you'll find basic pagination options.

Requested Article:

An investigation on failure behaviour of bonded polylactic acid adherends produced by 3D printing process: experimental and numerical approach
Özkan Öz, Fatih Huzeyfe Öztürk
Journal of the Brazilian Society of Mechanical Sciences and Engineering (2023) Vol. 45, Iss. 8
Closed Access | Times Cited: 10

Showing 10 citing articles:

Optimization of adherend thickness and overlap length on failure load of bonded 3D printed PETG parts using response surface method
Fatih Huzeyfe Öztürk
Rapid Prototyping Journal (2024) Vol. 30, Iss. 8, pp. 1579-1591
Closed Access | Times Cited: 4
Investigation of the Effects of Different Curing Methods on the Adhesion Strength of Single-Lap Joints Produced by Bonding 3D-Printed ABS and PLA Plates with Different Epoxy Adhesives
Muhammed Safa KAMER
Polymers (2025) Vol. 17, Iss. 6, pp. 768-768
Open Access
Influence of 3D printed adherend design on structural performance and vibrational behaviour of adhesively bonded joints
M. Rajesh, Raja Venkatesan, S. Kesavan, et al.
Journal of the Brazilian Society of Mechanical Sciences and Engineering (2024) Vol. 46, Iss. 7
Closed Access | Times Cited: 3
A response surface methodology investigation into the optimization of manufacturing time and quality for FFF 3D printed PLA parts
Abdurrahim Temiz
Rapid Prototyping Journal (2024) Vol. 30, Iss. 10, pp. 2007-2020
Closed Access | Times Cited: 3
Low-cost method to reduce interlayer voids in material extrusion: in situ layer-by-layer solvent treatment
Muhammed Saqlain Iqbal, Gianni Stano, Valentina Triminì, et al.
The International Journal of Advanced Manufacturing Technology (2024) Vol. 133, Iss. 11-12, pp. 5333-5342
Open Access | Times Cited: 1
Eklemeli İmalat Yöntemi ile Üretilmiş PLA Levhaların Bağlantı Dayanımları: İndüksiyonla Isıtma ve Yapıştırıcı Teknolojilerinin Karşılaştırılması
Mustafa Acaroğlu, Özkan Öz, Fatih Huzeyfe Öztürk
Afyon Kocatepe University Journal of Sciences and Engineering (2024) Vol. 24, Iss. 4, pp. 993-1004
Open Access | Times Cited: 1
Recent Advances in Adhesive Bonding of 3D-Printed Parts and Methods to Increase their Mechanical Performance
Daniel K. K. Cavalcanti, M. Medina, Henrique F. M. de Queiroz, et al.
Annals of Dunarea de Jos University of Galati Fascicle XII Welding Equipment and Technology (2023) Vol. 34, pp. 17-24
Open Access | Times Cited: 3
Heat‐Treatment and Water Immersion Effect on the Mechanical Properties and Joint Strength of 3D‐Printed Polylactic Acid Parts
Fatih Huzeyfe Öztürk, Özkan Öz
Polymers for Advanced Technologies (2024) Vol. 35, Iss. 11
Open Access
Strength improvement and failure analysis of dissimilar FDM printed single-lap joints with tailored interface geometry
Ishan Manoj, Atul Jain
International Journal of Adhesion and Adhesives (2024) Vol. 136, pp. 103876-103876
Closed Access
Investigation of failure loads of adhesive bonded and induction welded joints on similar and dissimilar substrates
Fatih Huzeyfe Öztürk
International Advanced Researches and Engineering Journal (2024)
Open Access
Page 1

Scroll to top