OpenAlex is a bibliographic catalogue of scientific papers, authors and institutions accessible in open access mode, named after the Library of Alexandria. It's citation coverage is excellent and I hope you will find utility in this listing of citing articles!
If you click the article title, you'll navigate to the article, as listed in CrossRef. If you click the Open Access links, you'll navigate to the "best Open Access location". Clicking the citation count will open this listing for that article. Lastly at the bottom of the page, you'll find basic pagination options.
Requested Article:
Impact of strain rate on mechanical properties of polylatic acid fabricated by fusion deposition modeling
M. BALASUBRAMANIAN, R. Saravanan, Vigneshwaran Shanmugam
Polymers for Advanced Technologies (2024) Vol. 35, Iss. 3
Closed Access | Times Cited: 8
M. BALASUBRAMANIAN, R. Saravanan, Vigneshwaran Shanmugam
Polymers for Advanced Technologies (2024) Vol. 35, Iss. 3
Closed Access | Times Cited: 8
Showing 8 citing articles:
Influence of Thermoplastic Polyurethane (TPU) and Printing Parameters on The Thermal and Mechanical Performance of Polylactic Acid (PLA) / Thermoplastic Polyurethane (TPU) Polymer
Muhammad Nafiz Hamidi, Jamaluddin Abdullah, Abdus Samad Mahmud, et al.
Polymer Testing (2025), pp. 108697-108697
Open Access | Times Cited: 1
Muhammad Nafiz Hamidi, Jamaluddin Abdullah, Abdus Samad Mahmud, et al.
Polymer Testing (2025), pp. 108697-108697
Open Access | Times Cited: 1
Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg)
Vukašin Slavković, Blaž Hanželič, Vasja Plesec, et al.
Polymers (2024) Vol. 16, Iss. 11, pp. 1526-1526
Open Access | Times Cited: 4
Vukašin Slavković, Blaž Hanželič, Vasja Plesec, et al.
Polymers (2024) Vol. 16, Iss. 11, pp. 1526-1526
Open Access | Times Cited: 4
3D printed polymeric stent design: Mechanical testing and computational modeling
Francesc Canalejo-Codina, Mariola Cano-Morenilla, Jordi Martorell, et al.
Materials & Design (2024), pp. 113395-113395
Open Access | Times Cited: 2
Francesc Canalejo-Codina, Mariola Cano-Morenilla, Jordi Martorell, et al.
Materials & Design (2024), pp. 113395-113395
Open Access | Times Cited: 2
Thermo-Mechanical Uniaxial Compression of 4D Printed PLA in Wide Range of Strain Rates and Temperatures below Glass Transition Temperature T<sub>g</sub>
Vukašin Slavković, Blaž Hanželič, Vasja Plesec, et al.
(2024)
Open Access | Times Cited: 1
Vukašin Slavković, Blaž Hanželič, Vasja Plesec, et al.
(2024)
Open Access | Times Cited: 1
Opportunities and challenges of bamboo fiber composites in additive manufacturing: A comprehensive review
M. BALASUBRAMANIAN, R. Saravanan, T. Sathish, et al.
AIP Advances (2024) Vol. 14, Iss. 9
Open Access | Times Cited: 1
M. BALASUBRAMANIAN, R. Saravanan, T. Sathish, et al.
AIP Advances (2024) Vol. 14, Iss. 9
Open Access | Times Cited: 1
Exploring the synergistic influence of FDM parameters and strain rate on tensile strength and failure mechanism of FDM printed PLA
M. BALASUBRAMANIAN, R. Saravanan, Yo-Lun Yang, et al.
Progress in Additive Manufacturing (2024)
Closed Access | Times Cited: 1
M. BALASUBRAMANIAN, R. Saravanan, Yo-Lun Yang, et al.
Progress in Additive Manufacturing (2024)
Closed Access | Times Cited: 1
Investigating the Influence of Strain Rate on Tensile, Flexural, and ILSS of Fused Deposition Modeling Printed PLA Polymer
M. BALASUBRAMANIAN, R. Saravanan, T. Sathish, et al.
Journal of Materials Engineering and Performance (2024)
Closed Access
M. BALASUBRAMANIAN, R. Saravanan, T. Sathish, et al.
Journal of Materials Engineering and Performance (2024)
Closed Access
Optimization of Printing Parameters of PLA and ABS Produced by FFF
İsmail Aykut Karamanlı, Kadircan Tahnal
Journal of Materials and Mechatronics A (2024), pp. 286-302
Open Access
İsmail Aykut Karamanlı, Kadircan Tahnal
Journal of Materials and Mechatronics A (2024), pp. 286-302
Open Access
